Kichler 42017 Manuale Utente Scaricare il pdf

11) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

12) Carefully push wire connections back into outlet box making

sure all connections remain secure.

13) Slip canopy over mounting screws and backpan. NOTE: Be

certain wires do not get pinched between backpan and

canopy.

14) Secure canopy to backpan using threaded caps.

15) Set glass down over socket.

16) Thread socket ring onto socket. (DO NOT over tighten.)

17) Insert recommended bulb. CAUTION: DO NOT touch bulb

with bare hands. If this happens, clean bulb with denatured

alcohol and a lint free cloth.

18) Slip glass sleeve over bulb.

LOOP/CHAIN LINK MOUNT

1) Follow steps 1, 2 and 3 from Stem Mount Instructions.

2) Screw loops onto end of each threaded pipe.

3) Add one chain link to each loop and add second loop to each

chain link.

4) Screw threaded pipe into end of each loop.

5) Pass each threaded pipe on loops through holes in canopy.

6) Slip one lockwasher over end of each threaded pipe and

screw one hexnut onto threaded pipes.

7) Follow steps 6 - 18 from Stem Mount Instructions.

IMPORTANT SAFETY INSTRUCTIONS

LIGHTED BULB IS HOT!

WARNING: To reduce the risk of FIRE or INJURY TO PERSON:

• Turnoffandallowtocoolbeforereplacingbulb.

• BulbgetsHOTQUICKLY!Contactswitchonlywhenturningoff.

• DONOTremaininlightifskinfeelswarm.(Lightisintense,

may cause “sunburn”)

• DONOTlookdirectlyatlightedbulb.

• Keepmaterialsawayfrombulbthatmayburn.

• UseONLYwithwattagespeciedorlower.

• DONOTtouchbulbatanytime,useasoftcloth.Oilfromskin

may damage bulb.

• DONOToperatexturewithmissingordamagedglass.

RIGID STEM MOUNT

1) Pass wire through stems and screw stems into couplings on

  topofxturebody.

NOTE: Thread locking compound must be applied to all stem

threads as noted with symbol (3) to prevent accidental

  rotationofxtureduringcleaning,relamping,etc.

2) Passxturewirethroughremainingstemsandscrewstems

together.

3) Screw small threaded pipe onto top of stems.

4) Pass holes in canopy over threaded pipe on top of stems.

5) Slip lockwasher over end of each threaded pipe and screw

hexnut onto end of each threaded pipe.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

   switch(s),thatcontrolthepowertothextureorroomthat

you are working on.

  c) Placethewallswitchinthe“OFF”position.Ifthextureto

be replaced has a switch or pull chain, place those in the

“OFF” position.

7) At the center of the backpan are knockout slots. Remove the

set that matches your outlet box.

8) Secure the backpan to the outlet box.

9) Anchor the backpan to the ceiling using the set of holes at

  eachendofxtureusingwoodscrews,togglebolts,plastic

anchors, etc.

10) Grounding instructions: (See Illus. A or B).

  A) Onxtureswheremountingstrapisprovidedwithahole

and two raise dimples. Wrap ground wire from outlet box

around green ground screw, and thread into hole.

  B) Onxtureswhereacuppedwasherisprovided.Put

ground wire from outlet box under cupped washer and

green ground screw and thread screw into hole

in mounting strap.

  Ifxtureisprovidedwithgroundwire.Connectxtureground

wire to outlet box ground wire with wire connector, (not

provided) after following the above steps. Never

connect ground wire to black or white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

IS-42017-USDate Issued: 12/28/12

LOOP/CHAIN LINK

LAZO/ ESLABÓN DE CADENA

BACKPAN

PLACADEMONTAJE

GLASS

VIDRIO

CANOPY

ESCUDETE

STEM

VARILLA

LOOP

ANILLO

CHAINLINK

ESLABÓNDE

CADENA

THREADEDPIPE

TUBO ROSCADO

STEM

VARILLA

RIGID STEM MOUNT

MONTAJE DEL VÁSTAGO NERVADO

THREADEDCAP

TAPA ROSCADA

THREADEDCAP

TAPA ROSCADA

HEXNUT

TUERCA

HEXAGONAL

BULB

BOMBILLA

GLASSSLEEVE

CAMISA DE VIDRIO

SOCKETRING

ANILLODEL

CASQUILLO

1 2

Sommario

Pagina 1

11) Make wire connections (connectors not provided.) Reference chart below for correct connections and wire accordingly.12) Carefully push wire

Pagina 2

11)Hacerlasconexionesdelosalambres(conectoresnoincluidos.) Ver el cuadro más abajo para las conexiones correctas y alambrar de acu

Modelli collegati 42432 | 43059 | 42436 | 65353 |

Commenti su questo manuale

Nessun commento

Kichler 42017 Manuale Utente

Navigare online o scaricare Manuale Utente per Illuminazione Kichler 42017. Kichler 42017 User Manual Manuale Utente

Sommario

Modelli collegati 42432 | 43059 | 42436 | 65353 |

Commenti su questo manuale

Prodotti e manuali riguardandi Illuminazione Kichler 42017